Explore Now

What are your thoughts regarding Tools You Need to Install a New Bathtub ?

Installing a tub isn't precisely rocket science, but it does require strong plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old bath tub with a brand-new one is likewise a moderately hard job. If the old tub is conveniently obtainable, the project can relocate easily; if you have to open up a wall to get rid of the old tub and also place the new tub, the task is a lot harder. In either instance, the job is within a residence handyman's skills, although you will need a helper to vacate the old bathtub as well as set in the brand-new one. Make sure you have certified on your own for the task and fit attempting it. Rather than working with a service provider to take over a halfway-completed project, it is much better to consider using one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This article will certainly help you mount a new bathtub in your bathroom if you have actually currently gotten a new tub and also do not require to alter the setup of your previous supply of water pipes.
Your tools and product list must make up the following:

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Removing Old Taps

If you require to change old taps with new ones as a part of your installation, after that the first thing you must do is disconnect the water system. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be quite troublesome because of the restricted gain access to that is often the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a cloth all set for the staying water that will certainly come from the pipes. When the supply pipes have actually been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this procedure. When the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Prior to carrying on to fit the brand-new faucets, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.

Suitable New Taps

If the tails of the new faucets are plastic, after that you will certainly need a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end provides a link to the current supply pipelines.
If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washing machines remain in location in between the faucet and also the sink. Protect the faucet in position with the producer provided backnut. As soon as the faucet is safely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet connectors. The previous type should be connected to the tap finishes initially, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.

Setting up the Bathtub

Making use of the two wooden boards under its feet, position the tub in the called for setting. The wood boards are practical in evenly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four little factors.
The following goal is to ensure that the tub is leveled all round. This can be attained by checking the level and changing the feet on the bath tub till the spirit level reviews level.
To mount faucets, fit all-time low of the furthest versatile faucet port to the proper supply pipeline by making a compression join; then do the very same for the various other faucet.
Turn on the water system and also inspect all joints and new pipework for leakages as well as tighten them if needed. Fill the bath tub as well as additionally check the overflow outlet and also the typical outlet for leakages.
Ultimately, repair the bathroom paneling as described in the supplier's instruction manual. Tiling and also securing around the tub ought to wait till the tub has actually been utilized at least when as this will resolve it into its last position.

Planning for the Installation

To start with, the sustaining structure supplied with the bathroom needs to be fitted (if required) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of the two taps using 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you utilize all of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final position.

Tiling Around the Bathtub

In the location where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to fracture a stiff seal, causing the water to pass through the wall in between the bath as well as the tiling, bring about complications with dampness and also feasible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and also fittings. They are sold in tubes and cartridges, and also can securing voids up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of soaked paper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to securing, to allow for the activity experienced when the bathtub remains in usage. The sealant can crack rather early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise quickly available on the market. It is recommended to fit the tiles making use of waterproof or water resistant adhesive and also cement.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

We are very eager about Installing A Bathtub and I am assuming you appreciated the entire article. Enjoyed our blog entry? Please share it. Help other people locate it. Thanks a lot for your time spent reading it.

Book Your Installation